|
#12070 Stanford
Stanford Mdl 142 30" wide doctor rewinder. 30" Maximum unwind roll diameter. 24" Maximum rewind roll diameter. 750 LB maximum roll weight. 1000 FPM maximum operating speed. Includes edge guide and air loaded layon roll on the rewind.
#12029 Beloit/Lenox
Beloit-Lenox 84" trim width two drum surface rewind slitter, shear cut slitting with bowed rolls before and after slitting, 20" diameter bed rolls, 60" diameter shaftless rewind, 3500 FPM.
#11966 Rotomec
Rotomec Rotopak 355/920 36" wide 8 color gravure press. New in 1984. Includes turret unwind and rewind with splicers for 32" diameter rolls, extend dryers on units 1, 7 and 8, 15" to 36" repeat range. AVT web video, uses cart system.
#11984 Black Clawson
Black Clawson 92" wide model DR-15 duplex rewind slitter rewinder complete with 3 ton bridge crane. Includes 100 HP drive (new in 2004), new Tidland light weight rewind shafts, shaftless unwind for a 62" diameter roll (loaded by overhead crane) with step chucks and Montalvo brake, 42” rewind diameter, new Tidland shear cut knife system, and misc. fittings and set-up parts and can run either center wind mode or surface/center. Machine in very good condition, can be seen in operation.
#12154 Dusenbery
Dusenbery Mdl. 800 EK 102" wide duplex center surface slitter rewinder. Includes a Dusenbery Mdl. 324 shaftless unwind with 60" O.D. capacity, 3" and 6" step chucks, Fife edge guide, 50" diameter rewind capacity, 3" Dia. Dif. rewind shafts, 1990. Like new condition. In storage.
#11993 Fischer & Krecke
One used Fischer & Krecke model 10 DF, 32" print width 8 color C.I. Flexo press with one flexo downstream station. Maximum web width is 33.75". Includes turret unwind and rewind for 40" diameter rolls, Enercon treater, 1/4 CP gearing, 10" to 25.5" repeat range, gas fired dryers, shear and razor slitting, temperature controlled CI drum and print deck frames. Print cylinders and anilox rolls are loaded into the press as sleeves (not lift out). This is a sleeved - geared press. New in 1997. In USA. Can be seen running.
#12156 Uteco
Uteco Amber 808, 8-color CI press. Mfg in 1998, this press has a printing width of 26" to 52 1/2", a Maximum repeat of 26.75", a Maximum roll diameter of 30", New Rotoflex chambered doctor blade units on all decks, BST video web.
#12104 Dusenbery/Futec
Dusenbery Model 835 duplex cantilevered center wind slitter; 46" max. web width, 24" max. rewind roll diameter, 1500 fpm, 3" min. slit width, shear slitting, SCM automated roll unloading, Futec two sided automatic defect detection system with 6 tabs.
#12090 Shanklin - Wexxar
Two Shanklin A-27A L-Sealers, Signature Packaging shrink tunnel model D2412-TMC, Action Packaging Systems label printer/applicator, Wexxar case erector, packing station and Little David case sealer.
#12133 Kidder
Kidder 660 45" print with press. Chambered doctor blades on all decks, 11"-33" print repeat (can be modified to extend repeat to 36"), 1/4cp gearing, fast rack back of decks, print section rebuilt 1993, dual burner gas drying, web scanner. New 1968
#11978 J-R Greene
J-R Greene, Inc. 34" wide two zone drying oven. Made up of two 20 foot long sections. Each has a 1.5 MM BTU/Hr. Maxon 415 "Ovenpak" burner and both input and exhaust blowers. Idler rolls form a gentle arch under 34" wide slot nozzels. The idlers are 36" face and tendency driven. Temperatures of 500 degrees F + are possible.
#11938 Independent
Independent (USA Built) "Jumbo" slitting/spooling line. Includes an unwind stand for a 28"+ wide, 80" diameter roll, shear cut slitting station, 8 jumbo spool rewinds that can wind 32" wide x 60" diameter spools on 6" cores. Rated line speed is 1500 FPM. New in 1996. Still installed in Europe. Price in USD.
#12041 Dusenbery
Dusenbery model 815 54" trim width duplex slitter rewinder. Includes a separate unwind stand for a 50" O.D. roll, shear cut slitting (2" minimum slit), 24" rewind diameter Max., layon rolls, two motor Eurotherm drives and PLC controls for 1500 FPM Max. speed. Also includes an Eastern Engraving embosser with two sets of pattern rolls. Ran .00035 unsupported foils through 15# to 65# paper in present usage.
#11885 ECH Will
ECH Will/Pemco complete cut size sheeting line for 8 1/2" x 11" and A-4 size 215.9 mm x 279.4 mm sizes. Line was new in 1986. The Will sheeter is Model SLK 480 UI, 6 pocket with 5 shaftless unwinds for 57" O.D. rolls, overhead bridge, tension controls and decurlers, slitting, dual rotary sheeting section with two knife blocks (11" and A4 cut off), gripper style pile delivery to a conveyor that transports the reams away from the sheeter. Packaging equipment options are available.
#12012 Comco
Comco 22" wide "Proglide MSP" 5 color in-line flexo press with a Kempsmith reciprocating diecutter. Includes a Martin unwind with butt splicer, 5 in-line flexo decks with gas dryers, chill rolls, dual rewind and a Kempsmith diecutter. New 1998.
#12050 Dynamic Air
Dynamic Air Dilute Phase Convey System for powdered materials that are non abrasive like flour or salt or chemicals. Includes a bag unloader, three bulk storage container unloaders with auger unloaders, metering, weighing, transporting system (high volume air) and two powder storage tanks. Auger feeders unload the storage tanks into two mixing (grinding) tanks with 40 HP Meyers mixers. Each of these tanks feeds to a 90" diameter x 48" deep mixing tank with a roll mixer and a paddle mixer. Allen Bradley PLC controls. Dismantled. No mezanine. New in 2004.
#12121 PCMC
PCMC "Avanti" 50" web width (49" print width) 8 color gearless CI flexo press. Inlcudes turret unwind and rewind with splicing for 32" diameter rolls, infinitely variable repeat from 14" to 32", 1000 FPM rated speed. New in 2003.
#11958 Webco
Webco model TDS-HD 66" face width surface rewind slitter rewinder. Includes a Webco MD-60 shaftless self loading unwind for a 72" diameter roll, shear slit, shaftless rewind to 60" O.O., 3000 FPM rated speed, built in J table for roll lowering, 1998
#12067 Bobst/Champlain
Bobst/Champlain web fed 8 color gravure printer with rotary cutter creaser line, 45" print width. Includes a Zerand 46" wide turret unwind with butt splicer and festoon, Bobst Lemanic DR 1150 rotary diecutter (1996) 1000 FPM.
#12060 Mercury
Mercury 28" wide web fed cutter/creaser line with 6 in-line flexo print units with chambered doctor blades. Turret unwind for 72" diameter rolls, splicer, in-line printers with gas fired station dryers, D/C, pin stripper and delivery.
#12148 Cobdin Chadwick
Cobden Chadwick 75" Web Width 6-Color C.I. Flexo Press, 60" diameter unwind & pope reel surface rewind. Chambered doctor blades on all decks. 1980's. Installed but not in production.
#11950 Johnstone
Johnstone model 6 - 72" wide duplex slitter rewinder. Includes a separate unwind with webguide, brake and tension controls for 50" diameter rolls, shear cut slitting, duplex surface/center rewind driven through clutches, 36" maximum rewind diameter. Recent upgrades to the drive, controls, brake, Etc. Speeds to 1000 FPM.
#11940 Totani
Totani model CS-60 pouch machine. Max. length and width: 19.7" x 23.6". Rated at 140 cycles/minute. Good for surgical, medical and Chevron Seal peelable type.
#12056 Esse CI
Esse CI 94" wide two side flame treater. New in 2007. Never installed. Built to treat coextruded cast films at speeds to 700 FPM and achieve a Dyne/CM level between 44 and 52 Max. Treater rolls are 106" face x 23.62" diameter. Built for USA installation, 480 Volt electrics and Allen Bradley SLC 500 PLC.
#12108 Stanford
Stanford Model 418 duplex center/surface wind slitter; 62" max. web width, 30" max. rewind roll diameter, 1000 fpm, 3" min. slit width, shear slitting, separate single position self loading shaftless unwind with 50" roll diameter capability.
#12136 Stevens
Stevens 21.5" wide 8 color in-line flexo press with rotary diecutter and a rewind for 10 to 24 point paperboard. Includes a Martin unwind with splicer and festoon for 60" diameter rolls, 8 flexo print units, rotary diecutting and a rewind.
#12094 W&H
W&H model 746, 62" print width 6 color central impression flexo press. Includes 40" diameter turret unwind and rewind with splicers, print repeat range is 12" to 40", 1/4 C.P. gearing, automatic deck positioning, Etc. Speed is rated at 1200 FPM. The press will come with W&H chambered doctor blades on all decks and 70 print cylinders. New in 1989. Excellent press.
#12005 Lenox
Lenox 61" wide CSS-10 cut size sheeter. Includes a turret unwind for 40" diameter rolls, tape applicator station, slitting for 7 piles out, sheeting, sheet counting, stacking in trays and double delivery conveyors.
#12145 M&W
M&W catalytic incinerator for Approx. 5600 Max. CFM. Ground level outdoor mount for easy removal. Fall 2009 inspection report of the unit and the catalyst, all looks good. The PLC is an Allen Bradley SLC500 5/03 replaced in 2007 by PEI.
#12101 Champlain
Champlain 36" wide gravure printer with web fed cutter/creaser line. Turret unwind for 72" diameter rolls, splicer and festoon, 7 gravure print units, two can back print, model C-42 36" wide diecutter with belt askew.
#12098 Atlas
Atlas 63" wide model CW2 duplex slitter rewinder. Includes a separate shaftless self loading driven unwind stand for a 48 diameter roll, razor in grooved roll and shear cut slitting, duplex rewind to 30" OD with air loaded lay-on rolls, swing out rewind mandrels for finished roll unloading, 1500 FPM, 1990.
#12111 Dusenbery
Dusenbery Model 800-DK duplex surface/center wind slitter; 46" max. web width, 30" max. rewind roll diameter, 1000 fpm, 5" min. slit width, shear slitting, separate Model 824-ND single position shaftless unwind with 46" roll diameter capability, Erhardt & Leimer edge/line guide system, splice detector.
#12132 Kidder
Kidder Model 660 Centraflex 6 CI flexo press, 45" print, new in 1997, new style print decks with auto deck positioning, chambered doctor blades, 12"-36"print repeat with motorized control of running and lateral register, 1/4cp gearing, video system.
#12110 Stanford
Stanford Model 338-C cantilevered duplex differential rewind center wind slitter; 62" max. web width, 24" max. rewind roll diameter, 1000 fpm, shear cut, 3" min. slit width, separate single position shaftless unwind, 50" OD.
#12045 Stanford
Stanford model 142 roll doctor machine 24" wide with unwind and rewind for 24" diameter rolls. Includes a 10 HP 440 Volt AC motor with Eddy current clutch for 1000 FPM speeds, 250# Max. roll weight. (Eddy current control is missing).
#12105 Rotomec
Rotomec Rotopak Universal 150 8 color gravure press; 45" max. web width, 43.5" max. print width, 18" to 36" repeat, KTI unwind for 50" Dia, turret rewind to 32". Bobst Registration and Vigitec defect detection system.
#12122 G&A
G & A turret rewinder 1600mm (63") wide 500mm (20") Max. rewind with auto core loading and dual shuttle type unwind. 3" ID rewind core machine with many setups including spacers, core boxes and unloading equipment.
#12146 Stanford
Stanford model 638 30" wide duplex rewind slitter. Includes cantilevered unwind for 32" diameter rolls, 3" air shaft, brake, tension controls and line or edge guiding, razor slitting, duplex differential rewind to 26" diameter rolls with air loaded lay-on rolls. Two motor drive. New in 1997.
#11930 Vits
Vits 35" wide slitter/sheeter for paper. 4 Pocket 8.5 X 11. Batch stacker that can be set up for any desired sheet counts. Sheet length is timing belt controlled. Martin Splicer unwind is limited to 28" paper width (3 pocket cut size). Presently set up for 11" cutoff. 1000 FPM on 500 sheet counts. 1995. Pemco 36 wrapper.
#11932 Propheteer
Propheteer model 2300, 23" wide 7 color in-line flexo press for paperboard printing. Includes single position unwind and rewind for 60" diameter rolls, gas drying, UV unit, 30" Max. repeat, 1/8 CP gearing, new 1995, rebuilt recently.
#12141 Telstar Engineering
Telstar Engineering 25" wide cold foil applicator. This unit is used to apply stamping foil like materials to a web without heated dies or platens. It applies a UV curable adhesive, laminates the foil from a roll, and strips off the film. New 2004
#12086 Moore & White
Moore and White R-75 Sheeter with a shaftless self loading unwind for 60" wide rolls, 72" Max OD, 12" cores. Includes decurling, slitting, two motor drive, overlapper and piler. New in 1987.
|
